Z109REG2-1

High performance universal converter

Z109REG2-1 is an advanced universal converter able to manage all analog signals (mA, V, PT100, Pt1000, Pt500, Ni100, TCs, Ohm) and convert / isolate it into mA/V standard signals. The device can be configured through dip-switches, PC software.

Z170REG-1

DC duplicator / isolator with universal input and 2 output

Z170REG-1 allows to convert and duplicate an analog signal (mA, V, PT100, Pt1000, Pt500, Ni100, TCs, Ohm) by 2 indipendents outputs (mA or V).

Z-8AI

8-CH analog input module / RS485

The Z-8AI is used to interface analog inputs (Voltage or current, also with bipolar range) with Modbus system. The modules is able to supply all 8 current loops at the same time.

Z201

AC current to DC isolator / converter

Z201 accepts an alternate current (5 or 10Aac) and provides an isolated analog output (mA or V). It disposes also of dip switches to set the output ranges.

Z-SG

Strain gauge input module with basic functions

 Z-SG is a strain gauge signal converter. Measurements taken using the 6-wires or 4-wires technique are available through Modbus-RTU serial protocol or the analog output. Sensitivity from 1 to 64mV/V, settable by DIP-switch for integer values

S400CL-1

Overvoltage protection for analog signals

S400CL-1 is a surge protection for measuring, control and regulation devices. The device is equipped with terminal blocks with protection multistage, screw connections and one disconnector.

S400HV-2

Type 2 surge arrester for power lines

Surge protection for power supplies ( SPD Class II , Type 2 ) , for 3 conductors systems ( L1 , N , PE ) and for TT / TN – S

ATR121-AD

1 Analogue Input + 2 Relays 8 A + 1 SSR

ATR121-AD is using to display the temperature sensor (RTD: P100, Ni100,… TCs: K, R, S…) and the other linear signals (0-10V, 4-20mA, 0-40mV). Moreover, it’s use to display the potentionmeter.

ATR144-ABC

1 analogue input + 2 relays 5 A + 1 D.I/O 

ATR144-ABC is using to display the temperature sensor (RTD: P100, Ni100,… TCs: K, R, S…) and the other linear signals (0-10V, 4-20mA, 0-40mV). Moreover, it’s use to display the potentionmeter, NTC, PTC…

ATR244-12ABC

1 analogue input + 2 relays 2 A + 2 SSR + 2 D.I. + 1 analogue output V / mA

ATR244-ABC is using to display the temperature sensor (RTD: P100, Ni100,… TCs: K, R, S…) and the other linear signals (0-10V, 4-20mA, 0-40mV). Moreover, it’s use to display the potentionmeter, NTC and PTC…

STR551-12ABC-T

1 analogue input + 2 relays 2A + 1 Out 0..10V + 1 Out 0/4..20mA + RS485 

STR551 is using to display the temperature sensor (RTD: P100, Ni100,… TCs: K, R, S…) and the other linear signals (0-10V, 4-20mA, 0-40mV). Moreover, it’s use to display the potentionmeter, NTC and PTC…

S311A-4

Universal analog input indicator – totalizer

S311A-4 is using to display the temperature sensor (RTD: P100, Ni100,… TCs: K, R, S…) and the other linear signals (0-10V, 4-20mA). Moreover, it’s use to display the potentionmeter…

T201

Loop-powered AC current transducer

T201 is an alternating current transducer (CT) for 4..20 mA current loops (2-wire loop-powered technology).

T201DCH100-LP

AC/DC contactless TRMS

T201DCH100-LP is an isolated, contact-less loop-powered AC/DC current transducer [current (± 100 A) transducer, Hall Effect with 4..20 mA AO] READ MORE

T201DCH300-Mu

AC/DC contactless TRMS

T201DCH300-MU is an isolated, contact-less direct and alternating TRMS current transducer with ModBUS interface, analog output /alarm output, and micro USB port.

T203PM100-Mu

Single-phase power meter

T203PM100-MU is a single-phase AC/DC TRMS network power meter with ModBUS interface, analog, and digital output, inputs with a current measurement range up to 100 A, and for voltage 290 Vac, 1000 Vdc.

R-KEY-LT

ModBUS industrial gateway / serial device server

The R-KEY-LT (HW rev. C0) is a compact and robust Modbus gateway capable of transmitting signals between ModBUS TCP-IP/ ModBUS RTU in different modes, effectively increasing the number of nodes that can be connected and the distances that can be reached in the network thanks to 5 operating modes

Z-LTE-WWW

4G LTE WW Datalogger

4G LTE World-Wide high-performance modem, GPS receiver, 4 integrated communication ports (Ethernet, RS232, RS485, MicroUSB), 8 integrated I/O channels (4DI/meters/totalizers, 2AI, 2DO) further improved power supply range, voice alarms/audio controls…

Z-4AI

4-CH analog input module / RS485

Z-4AI is used to interface analog inputs (Voltage or current, also with bipolar range) with Modbus system. The modules is able to supply all 4 current loops at the same time, this is very useful for 2-wire sensors.

S401-L

ModBUS RTU indicator with OLED

These display utilise OLED technology (Organic LED technology). OLED displays have a rapid response time, wide viewing angles, exceptional colour rendition and outstanding contrast and brightness display ratios.

PRESSURE gauge

What is it?

Vacuum pressure gauge is an equidment for measuring the vacuum pressure.

PRESSURE Gauge

How’s it work?

A vacuum pressure gauge still has a bourdon tube in it. When the vacuum pressure happens, it makes the bourdon to shink. So, it leads to the Pointer rotate counter-clockwise.

pressure Gauge

What is the applicaiton?

A vacuum pressure gauge is used to know some machines’ vacuum pressure.

PRESSURE gauge

What is it?

Hydraulic pressure gauge is an equidment for measuring the highest pressure from hydraulic compressor and so on. Normally, it will has the pressure range from 0-100 bar, 0-250 bar…

 Pressure Gauge

How’s it work?

A hydraulic pressure gauge also has a bourdon tube in it. Their responsibility is measure the pressure of liquid or gas. When the liquid or gas move into the bourdon tube. It makes the bourdon expanding….

 Pressure Gauge

What is the application?

Nowadays, A hydraulic pressure gauge normally is using for measuring where it has the highest pressure such as hydraulic machine…

PRESSURE TRANSMITTER

What is it?

Pressure transmitter is an equidment using for measuring the pressure of liquid or gas. And then, the pressure transmitter will transfer the sigals into Analog signals 4-20mA/0-10V.

PRESSURE TRANSMITTER

How’s it work?

A Pressure transmitter will has an electronic membrane used to measure pressure. The higher the pressure of liquid or gas is, the higher the analog signals have…

PRESSURE TRANSMITTER

What is the application?

Nowadays, A Pressure transmitter will using for measuring of the pressure of liquid or gas in some systerm. Chiller, tubes, Chio, Sealed water tank, for example. So, it has a lot of type of measurement: 0-10bar, 0-40bar, 0-250bar…

CAPACITIVE LEVEL SENSOR

What is it?

A capacitive level sensor is used to measure the continuous water level and transform it into an analog signal.

CAPACITIVE LIMIT SENSOR

What is it?

A capacitive limit sensor is a sensor used for informing the limit of liquid

TEMPERATURE SENSOR

What is it?

A temperature sensor is a sensor used for decection of temperature of the enviroment.